|
Fire Detection Downloads Australia and New Zealand
|
Go to MX1-NZ
Go to FP1600
Go to MX1-Au
Go to MX4428
Go to F3200
Go to IO-NET
Go to QE90
Go to T-Gen2
Go to 4100ESi
|
|
|
|
MX1-NZ Fire Alarm System |
|
MX1COST MX1-NZ Estimating Package (SF0471) V2.21 (10.3MB)
No Price Engineering |
MX1-NZ Estimating
Package for New Zealand. This version does not include any pricing, so can be
used for engineering and design checking systems. Refer to
PBK0012V for details.
MX1CAL is also needed for doing I.S. design and loop
calculations. |
|
|
MX1CAL - MX1 Loop & Battery Calculator (SF0332) |
MX1CAL is an MX1
loop and battery/charger calculation program for earlier MX1
panels. This is V1.10, which supports up to two MX1 loops.
Download the file, extract the spreadsheet and use it as
the master. Copy and rename for each project. It can also be used for
multi-loop systems for doing IS calculations per loop. |
|
|
|
SmartConfig
MX1 Site Specific Data File Programmer V2.9.2.0 (SF0432) (6MB) |
This specific version of SmartConfig is for NZ MX1 resellers only.
Refer
PBK0024I for details. It requires licensing.
|
|
|
|
MX1 Panel Controller Firmware V1.80 (SF0295) |
This file contains MX1 V1.80 firmware
(refer
PBK0033).
Note: it is NOT included in the latest SmartConfig, so can be downloaded using this file.
The original 1.00, 1.20 and 1.34 versions of firmware have now been replaced with equivalent A versions that can be
downloaded into the original PA1011 MX1 Controller or the new PA1081 MX1 Controller.
|
|
|
|
850EMT Firmware V1.8 |
The file contains the 850EMT firmware V1.8
(refer to
PBG0204C. New
firmware for the 850EMT. Instructions for programming the 850EMT are contained in Section 6.2 of the 850EMT User Manual
LT0586. |
|
|
|
Zone Naming Label Template (LT0369) |
A Word document that can be downloaded, filled in with zone names and
printed. Then cut out and inserted into the zone labelling area on the MX1
front panel or the 80 zone LED display door (ME0457). |
|
|
|
MX Loop Card Firmware V2.07 (SF0392) |
The file contains the MX1-Au Loop Card firmware V2.07 (refer to
PBK0005E).
It includes an improvement to give better MX loop open circuit detection as required for NZS 4512.
V2.07 must be used with V1.40 MX panel firmware onwards and can be used with the earlier V1.33 version. |
|
|
|
FlashSimple Installer Program |
This file is an installation program that will install the
FlashSimple program needed for downloading new software to the MX
Loop Card. Run the FlashSimpleSetup.exe program and follow the
on-screen instructions. The default settings are: H8/3067F,
Direct Connection, COM1, 19200, BOOT mode. When used for the first
time, browse and select the file to download. Save the settings when
prompted when the program is closed after finishing. The
current location of the file to download will be saved as default for when
the program is run next time. |
|
PanelX Remote Communications Software V3.0
(SF0281) |
PanelX is a program for
remotely logging on to and controlling MX1, F3200, NDU, F4000, MX4428,
Compact FF, or Nurse Station Annunciator CIE that have firmware
supporting Tandem Mode operation. The program controls the CIE via an
emulation of the user interface on the PC and supports direct RS232
connection, dialling up using a modem, and a TCP/IP network connection.
Version 3 supports MX1 Australia with FBP, Windows Vista, serial port
details programmable per connection and various enhancements and
stability improvements. To install the program run the SF0281 file and
set up the connection details for the CIE to be accessed. Further
information is contained in the Help file that is included in the
program or in Product Bulletin
PBF0226B. |
|
|
|
|
|
|
|
Top of Page
|
|
FP1600 Fire Alarm System |
|
|
|
|
SF0287 |
FlashX is a Windows program for downloading new firmware (software)
into Mk3 versions of FP1600. This file contains V5.02 for FP1600 and Omega 64 Masters, and V5.02 for Omega 64 slaves which are NZS4512:2010 compliant. |
|
|
|
|
SF0323 |
SmartConfig LITE is a Windows program for
preparing T-Gen2/FP1600/Omega 64 (V5.00) database file and downloading it
to the panel. It can also upload an existing database from a
panel that has V4.XX or V5.XX software. |
|
|
|
|
LT0345 |
SmartConfig LITE User Manual for programming T-Gen2, FP1600 or IO-NET. |
|
|
|
|
Top of Page
|
|
MX1-Au Fire Alarm System |
|
|
|
MX1COST MX1-Au Estimating Package (SF0477) V2.21 (38MB)
No Price Engineering |
MX1-Au Estimating Package for Australia.
Features include support for new MX1 stock panels and flame detectors.
This version does not include any pricing, so can be used for engineering and design checking systems.
Refer to
PBK0012V for details.
MX1CAL is also needed for doing I.S. design and loop
calculations. |
|
|
|
MX1CAL - MX1 Loop & Battery Calculator (SF0332) |
MX1CAL is an MX1
loop and battery/charger calculation program for earlier MX1
panels. This is V1.10, which supports up to two MX1 loops.
Download the file, extract the spreadsheet and use it as
the master. Copy and rename for each project. It can also be used for
multi-loop systems for doing IS calculations per loop. |
|
|
|
SmartConfig
MX1 Site Specific Data File Programmer V2.9.2.0 (SF0432) (6MB) |
This version of SmartConfig supports MX1, T-Gen2 and IO-Net only, and is suitable for external (non-Johnson Controls) users.
V2.9.1.0 includes support for the MX P80SB, P80AVB, P81AVB and P80AVW
and VAD devices and MX1 firmware V1.80. It requires licencing.
Refer
PBK0024I for details.
|
|
|
|
MX1 Panel Controller Firmware V1.80 (SF0412) |
The file contains the MX1-Au Controller firmware V1.80 (refer
PBK0033) and the earlier V1.33A (refer PBK0004A).
Note: the MX1 V1.71 firmware is NOT included in the latest SmartConfig, so can be downloaded using this file.
|
|
|
|
850EMT Firmware V1.8 |
The file contains the 850EMT firmware V1.8
New firmware for the 850EMT
(refer to
PBG0204C).
Instructions for programming the 850EMT are contained in Section 6.2 of the 850EMT User Manual
LT0586. |
|
|
|
Zone Naming Label Template (LT0369) |
A Word document that can be downloaded, filled in with zone names and
printed. Then cut out and inserted into the zone labelling area on the MX1
front panel or the 80 zone LED display door (ME0457). |
|
|
|
MX Loop Card Firmware V2.07 (SF0392) |
The file contains the MX1-Au Loop Card firmware V2.07 (refer to
PBK0005E).
It includes an improvement to give better MX loop open circuit detection as required for NZS 4512.
V2.07 must be used with V1.40 MX panel firmware onwards and can be used with the earlier V1.33 version. |
|
|
|
FlashSimple Installer Program |
This file is an installation program that will install the
FlashSimple program needed for downloading new software to the MX
Loop Card. Run the FlashSimpleSetup.exe program and follow the
on-screen instructions. The default settings are: H8/3067F,
Direct Connection, COM1, 19200, BOOT mode. When used for the first
time, browse and select the file to download. Save the settings when
prompted when the program is closed after finishing. The
current location of the file to download will be saved as default for when
the program is run next time. |
|
PanelX Remote Communications Software V3.0 (SF0281) |
PanelX is a program for
remotely logging on to and controlling MX1, F3200, NDU, F4000, MX4428,
Compact FF, or Nurse Station Annunciator CIE that have firmware
supporting Tandem Mode operation. The program controls the CIE via an
emulation of the user interface on the PC and supports direct RS232
connection, dialling up using a modem, and a TCP/IP network connection.
Version 3 supports MX1 Australia with FBP, Windows Vista, serial port
details programmable per connection and various enhancements and
stability improvements. To install the program run the SF0281 file and
set up the connection details for the CIE to be accessed. Further
information is contained in the Help file that is included in the
program or in Product Bulletin
PBF0226B. |
|
|
|
|
|
|
|
Top of Page
|
|
MX4428 Fire Alarm System |
|
|
|
|
SF0250 MXP Firmware V1.22 |
A zip file containing the MXP software, MXPPROG & MXPPROG32 download programs,
and instructions so that the MXP's FLASH that contains the operational software may be updated.
Unzip the files into the required directory and read the Readme.txt file.
Note: do not use any old copies of these programs when downloading V1.22 to an MXP (they won't work).
|
|
|
|
850EMT Firmware V1.8 |
The file contains the 850EMT firmware V1.8 (refer to
PBG0204B).
New firmware for the 850EMT.
Instructions for programming the 850EMT are contained in Section 6.2 of the 850EMT User Manual
LT0586. |
|
|
|
|
MX442 Programming Software
SmartConfig Plus V2.9.2.0 (SF0278) (7MB) |
A
Windows program for programming the database for MX4428 (F4000 with
V3.XX onwards) systems.
V2.9.2.0
is the latest (no
changes for MX4428). Refer PBF0282I for
details. To use this software correctly and receive technical
support you must have completed MX4428 training in the last 24 months
and have sound industry experience with F4000/MX4428. |
|
|
|
|
|
|
|
Top of Page
|
|
F3200 Fire Alarm System |
|
|
|
|
SF0287 FlashX Firmware V1.03B |
FlashX is a Windows program for downloading new firmware (software) into Version
4 and 5 of F3200, NDU, FP1600 Mk3, Omega 64 Mk3, all versions of Compact FF and Nurse Station ADUs and version 5.xx of the RDU.
Further details are contained in Product Bulletin PBG0125D
. The SF0287.exe file is an installation program that will install FlashX and the
firmware files to download. Once installed, you "add" the contained firmware files, and then download the required file.
The on-line help file contains instructions for programming each product. V1.03B of FlashX contains V5.02 for F3200 and NDUs,
V4.04 for older F3200 and NDUs, V5.00 for ADUs, and V5.00 for the RDU.
|
|
|
|
|
Zone Naming Label (LB0298) |
A Word document laid out to enter the zone names to make
the zone naming label that you fit onto an F3200.
Download this file, type in the text names, print it, cut
off the excess paper and fit to the F3200 64 Zone LED
Display window. This suits both the perspex window and the slide-in mylar arrangement of ME0060. |
|
|
|
|
F3200 Gaseous Fire Extinguishing Panel Database (SF0277.s28)
F3200 Gas Panel Database - Plain Text |
A ZIP file containing a database for an F3200 gas panel using V4.XX software
that can be downloaded to give a starting point in the
programming. Programming is as per LT0255 Section 6.2 and
as supplied in FP0876, FP0877 and special F3200 gas
panels. |
|
|
|
|
F3200 Battery Calculation Spreadsheet V1.0 (SF0345)
|
An Excel spreadsheet that allows entry of the F3200 panel
options and for the battery capacity to be calculated. Run the SF0345.exe file
to install the spreadsheet on to your computer. You will need to have Excel
installed to use this. |
|
|
|
|
RDU Mk1 Database Convert to Mk2 V5.xx (SF0425)
|
When upgrading an RDU from V2.xx to V5.xx it is necessary to capture the existing database to a
PC and upgrade it using this Database Converter Program, otherwise the database must be completely re-entered.
Details on using this program is covered in Section 7.6 of the RDU Mk2 Installation & Programming Manual LT0499.
Extract the three files in the zip file and put into the directory
where the existing RDU database file is for ease of use. |
|
|
|
|
Top of Page
|
|
IO-NET |
|
|
|
|
SF0323 |
SmartConfig LITE is a Windows program for preparing an IO-NET (V2.xx)
database file and downloading it to the controller. It can also read an existing database from earlier controller software versions.
|
|
|
|
|
Top of Page
|
|
QE90 EWIS |
|
|
|
|
LT0216 |
Zone naming label for QE90 fascia as Word File.
|
|
|
|
|
LT0613 |
An Excel spreadsheet QE90 EWIS Configuration form that can be filled in electronically and emailed
to us for manufacturing. Right click the link and Save As... to download the file. Issue 5.
|
|
|
|
|
Top of Page
|
|
T-Gen2 |
|
|
|
|
SF0323 |
This is an unlicenced version of SmartConfig that can be used to create custom configuration for T-Gen2 units.
This version supports T-Gen2 Grade 2.
Refer Product Bulletin
PBG0209C and LT0345 for details.
|
|
|
|
|
SF0534 V2.50 |
New firmware for T-Gen2. Supports Grade 3 and Grade 2 operation.
Many new features and improvements have been included. Existing V1.xx T-Gen2 can be upgraded. Refer Product Bulletin
PBG0216G for information. |
|
|
|
|
SF0534 V1.12 |
Updated V1.12 firmware for T-Gen2 to increase the emergency speech and paging volume from the built-in microphone and remove Amplifier Faults being
generated on long speaker cables. Refer Product Bulletin
PBG0216G. |
|
4100ESi |
|
|
|
|
Security Services 2.04 |
Security Package required
to allow the programming dongle or license to work.
|
|
|
|
Top of Page
|
|
|
|
|
|
|